Articles


Boeing Partners with Queensland Government on Autonomous Vehicle Research

During the next three years, this rapid innovation program will see Boeing develop next-generation autonomous systems capability in Australia to increase the independent operation of air and sea vehicles.

OSHA to Start Enforcing New Beryllium Rule in May

OSHA said it also will begin enforcing on May 11, 2018, the new, lower 8-hour permissible exposure limit and short-term (15-minute) exposure limit for construction and shipyard industries.

France Ratifies Fishing Vessel Safety Agreement

The Cape Town Agreement will take effect 12 months after it has been ratified by 22 states that, collectively, have 3,600 or more fishing vessels of at least 24 meters in length operating on the high seas.

Six FDNY EMS Veterans Promoted

The six have prepared the bureau's emergency response to major events and have managed mass casualty incidents across the five boroughs, ensuring the safety of millions of New Yorkers and tourists.

New FMCSA, FRA Administrators Sworn In

FMCSA's Raymond P. Martinez is a former commissioner of the New York State Department of Motor Vehicles. FRA's Ronald L. Batory was president and chief operating officer of Conrail, the eighth-largest freight railroad in America, from 2004 until his retirement in April 2017.

NIOSH Offering Confidential Black Lung Screenings for Coal Miners

The free health screenings are provided through NIOSH mobile testing units. They will begin March 19-23 in coal mining regions throughout Western Kentucky and then take place the following week, March 26-30, throughout Mingo, Logan, and Wayne Counties in West Virginia.

NTSB Issues Brief on 2016 Tanker Accident

Two pilots aboard the vessel suffered minor burns in the fire. The accident caused an estimated $1.5 million in property damage.

Fall Protection Training - Protective Equiment Alone is Not Enough to Keep Workers Safe

Fall Protection Training - Protective Equiment Alone is Not Enough to Keep Workers Safe

In 2016, a total of 5,190 fatal work injuries were recorded in the United States, a 7% increase from the fatal injuries reported in 2015.1 This is the third consecutive increase in annual workplace fatalities in the United States.



Developing an Effective Injury and Illness Prevention Program to Proactively Address Heat-Related Risks

As we move into the summer months of 2018, a company's hazard assessment should include consideration for the impact excessive heat plays, or could play, in its work environment.

Oregon Pesticide Rule Still Open for Comments

The proposal would add protections to EPA's Application Exclusion Zone, which surrounds and moves with pesticide-spray equipment during applications. It must be free of all people other than appropriately trained and equipped pesticide handlers.

Dallas Neighborhood's Gas Cutoff Affects 2,800 Homes

Atmos Energy says its planned outage for up to three weeks is being done "out of an abundance of caution" and "is not being taken because of any imminent emergency or danger," but a gas explosion Feb. 23 that killed a 12-year-old girl in her home spurred the repairs.

NCCCO Says Don't Sit Out OSHA's One-Year Delay

"It's not the first time the industry has had to come to terms with an extension of this rule, but, in the minds of most safety-conscious professionals, this should not be a reason to further delay training and certification," said NCCCO CEO Graham Brent.

The hazmat rules are constantly under construction, with a new requirement or restriction always on the horizon. (Lion Technology Inc. photo)

Is America's Hazmat in Good Hands?

Yes, for now. But the world will need a new crop of dedicated dangerous goods professionals to ensure hazmat reaches its destination, safely and on time.

Ejection Seat Manufacturer Fined $1.4 Million in Red Arrows Pilot's Death

An investigation by the Health and Safety Executive concluded a mechanical fault led to the failure of the parachute deployment mechanism designed to bring the 35-year-old pilot to ground safely, and this resulted in the main parachute failing to deploy.

NIOSH's Pocket Guide Turns 40

Improving the NPG will be helpful to all of us.

Preparing for Automated Driving Systems

Weighty questions about the technologies include how the current standard for stability control testing can be amended for ADS vehicles that have no steering wheel.

Safe Sounding Workplaces

Using sound mapping software rather than measurements means you can predict future noise levels and take pre-emptive steps to control the noise.

Fatal Fall Brings $40,096 Fine

OSHA investigated the company after an employee installing patio screen enclosures died from a fall. L.I. Aluminum was issued four serious citations for failing to provide fall protection to employees working at heights of 10 feet or more; exposing employees to falls; and failing to train employees on fall hazards and the proper use of ladders.

Lockout leadership can be the missing link that drives continuous improvement leading to meaningful change in the safety culture of the adapting workplace. (The Master Lock Company photo)

Lockout Leadership as a Path to Advancing the Practice

It is much more effective to share with workers the ways and means the company has decided to do things, rather than let impersonal government regulations drive critical behaviors.

Even if employees do remember all of the layers of protective equipment they need, the inconvenience of having to put on and take off multiple items may deter them from wearing all of the necessary PPE. (Workrite Uniform Company photo)

PPE Tips for Encouraging Wearer Compliance

The best way to prevent costly injuries is to promote safe work practices, provide the necessary PPE, and do everything possible to encourage wearer compliance.

Product Showcase

  • Magid® D-ROC® GPD412 21G Ultra-Thin Polyurethane Palm Coated Work Gloves

    Magid’s 21G line is more than just a 21-gauge glove, it’s a revolutionary knitting technology paired with an advanced selection of innovative fibers to create the ultimate in lightweight cut protection. The latest offering in our 21G line provides ANSI A4 cut resistance with unparalleled dexterity and extreme comfort that no other 21-gauge glove on the market can offer! Read More

  • SwabTek® Cannabis Test Kit

    The SwabTek® Cannabis Test Kit is a single-use spot test designed for use in screening for cannabis compounds in any sample type or on any surface. The test is capable of identifying the presumed presence of cannabinoids in very small quantities, with a level of detection as little as 6 μg in mass. Learn more about the SwabTek® Cannabis Test Kit and the rest of SwabTek surface drug testing solutions through the webinar titled "Everything You Want To Know About Surface Testing" Read More

  • Safety Knives

    The Safety Knife Company has developed a quality range of safety knives for all industries. Designed so that fingers cannot get to the blades, these knives will safely cut through cardboard, tape, strapping, shrink or plastic wrap or a variety of other packing materials. Because these knives have no exposed blades and only cut cardboard deep, they will not only protect employees against lacerations but they will also save product. The Metal Detectable versions have revolutionary metal detectable polypropylene knife bodies specifically for the food and pharmaceutical industries. This material can be detected and rejected by typical detection machines and is X-ray visible. Read More

Featured

Artificial Intelligence