Workplace Injuries Rise Following Daylight Savings Change

Using U.S. Department of Labor and Mine Safety and Health Administration data, Christopher Barnes and David Wagner, both doctoral candidates studying industrial and organizational psychology at Michigan State University, found that the number of workplace accidents spikes after Daylight Savings Time changes every March.

On the other hand, they found no significant increase in workplace accidents or sleep loss when the clocks were set back an hour in November.

In two separate studies, they found that the March switch to Daylight Savings Time resulted in 40 minutes less sleep for American workers, a 5.7 percent increase in workplace injuries, and nearly 68 percent more work days lost to injuries.

The research will be reported in the September issue of the Journal of Applied Psychology.

But can losing one hour of sleep really make a difference? "Yes," said Barnes, "it can. Especially for those engaged in jobs requiring a high level of attention to detail. Studies have shown that lost sleep causes attention levels to drop off."

Because of this, some industries, like trucking and airlines, have regulations setting limits on the consecutive hours that truckers can drive or crews fly without taking a break.

Barnes and Wagner noted that some researchers claim the one-hour clock adjustment does not, and could not, impact accident rates in organizations. "We contend that the springtime change is associated with an increase in the number and severity of workplace accidents," the said.

There is other research available that tends to support Barnes and Wagner. A University of British Columbia study, using data from the Canadian Ministry of Transport, found that when Canada went into daylight savings time, there was an 8 percent increase risk of accidents on the Monday after the changeover. A similar study, using information from the U. S. National Highway Traffic Safety Administration, cited sleep deprivation as the most likely cause of a 17 percent increase in accidents on the Monday following the time change.

Barnes pointed out that is not uncommon for people to complain how tired they are when they lose sleep. Many people adjust to a pace where events recur regularly and they can be adversely affected when that schedule is disrupted. An obvious example is jet lag, which occurs when people travel across several time zones.

"Their internal clocks need some recovery time for these kind of disruptions," Wagner said.

Barnes noted that people assume the change to Daylight Savings is not going to greatly affect them. After all it's only one hour. And if they do have an accident or make a mistake, they are not likely to attribute it to sleep loss.

While their study focused on physical accidents, Barnes and Wagner said a logical extension could be mistakes in the office or workplace, such as transposing figures on a spread-sheet or filling the wrong prescription in a pharmacy.

The researchers used figures from the American Time Use Survey conducted by the Bureau of Labor Statistics, which included more than 14,000 interviews. They also studied data from the Mine Safety and Health Administration. In analyzing those figures, it was clear that people lost an average of 40 minutes of sleep following the change to Daylight Savings and there was a jump in workplace accidents following the time change.

They also looked at all Mondays in a year and allowed for seasonal effects and other factors. For example, there is more likelihood of snow in Michigan and Minnesota in March than in other parts of the country and the bad weather may have been more of a contributing factor to accidents than the time change.

However, the results clearly show that sleep does have a profound effect upon human behavior and lack of sleep can have significant and serious results, researchers said.

Product Showcase

  • The MGC Simple Plus

    The MGC Simple Plus is a simple-to-use, portable multi gas detector that runs continuously for three years without being recharged or routinely calibrated after its initial charge and calibration during manufacturing. The detector reliably tests a worksite’s atmosphere for hydrogen sulfide, carbon monoxide, oxygen and combustible gases (LEL). Its durability enables the detector to withstand the harshest treatment and environments, hence earning it an IP 68 rating. The MGC Simple Plus is also compatible with a variety of accessories, such as the GCT External Pump. Visit gascliptech.com for more information. 3

  • Safety Knives

    The Safety Knife Company has developed a quality range of safety knives for all industries. Designed so that fingers cannot get to the blades, these knives will safely cut through cardboard, tape, strapping, shrink or plastic wrap or a variety of other packing materials. Because these knives have no exposed blades and only cut cardboard deep, they will not only protect employees against lacerations but they will also save product. The Metal Detectable versions have revolutionary metal detectable polypropylene knife bodies specifically for the food and pharmaceutical industries. This material can be detected and rejected by typical detection machines and is X-ray visible. 3

  • AirChek Connect Sampling Pump

    Stay connected to your sampling with the SKC AirChek® Connect Sampling Pump! With its Bluetooth connection to PC and mobile devices, you can monitor AirChek Connect pump operation without disrupting workflow. SKC designed AirChek Connect specifically for all OEHS professionals to ensure accurate, reliable flows from 5 to 5000 ml/min and extreme ease of use. AirChek Connect offers easy touch screen operation and flexibility. It is quality built to serve you and the workers you protect. Ask about special pricing and a demo at AIHA Connect Booth 1003. 3

Featured