NTSB Cites Tire, Bridge Railing Failure in Fatal 2008 Motorcoach Crash

The National Transportation Safety Board today determined that the probable cause of a fatal motorcoach accident in Sherman, Texas, was the failure of the right steer axle tire, due to an extended period of low-pressure operation, which resulted in sidewall, belting, and body ply separation within the tire, leading to loss of vehicle control.

Contributing to the severity of the accident was the failure of the bridge railing to redirect the motorcoach and prevent it from departing the bridge. The lack of an adequate occupant protection system contributed to the severity of the passenger injuries.

The accident occurred on August 8, 2008, when a 2002, 56-passenger motorcoach with a driver and 55 passengers on board departed Houston en route to a festival in Carthage, Mo. About four-and-a-half hours into the trip while traveling northbound in the right lane of U.S. Highway 75, the right steer axle tire failed as the motorcoach approached the Post Oak Creek bridge at a speed of about 68 mph; the bus went through the bridge railing and off the bridge. It fell about 8 feet and slid approximately 24 feet on its right side before coming to rest. As a result of the accident, 17 passengers died. In addition, the driver received serious injuries and 38 passengers received minor-to-serious injuries.

Major safety issues identified by this accident investigation include the following safety issues:

  • The tire failure and the need for tire pressure monitoring systems on vehicles more than 10,000 pounds.
  • The failure of the bridge railing and the need for criteria for the selection of appropriate bridge railing designs.
  • The lack of oversight of the federal commercial vehicle inspections that are delegated to the states.
  • The lack of motorcoach occupant protection systems.
  • The deficiencies in federal safety oversight of new entrant motor carriers.

As a result of its investigation of this accident, NTSB made eight new recommendations in these five safety issue areas to three federal agencies: the Federal Highway Administration , the Federal Motor Carrier Safety Administration (FMCSA), and the National Highway Traffic Safety Administration (NHTSA).

Two recommendations were made to the American Association of State Highway and Transportation Officials in the area of bridge railing design and one recommendation to the American Association of Motor Vehicle Administrators regarding tire pressure monitoring procedures, and one recommendation was made to the motorcoach manufacturer, Motor Coach Industries, Inc., calling for revised vehicle maintenance manuals.

NTSB also reiterated five previous recommendations made to FMCSA and NHTSA in the areas of drug and alcohol testing and motorcoach occupant protection systems.

A synopsis of NTSB's report, including the probable cause and recommendations, is available on its Web site, www.ntsb.gov, under "Board Meetings." The full report will be available on the Web site in several weeks.

Product Showcase

  • Magid® D-ROC® GPD412 21G Ultra-Thin Polyurethane Palm Coated Work Gloves

    Magid’s 21G line is more than just a 21-gauge glove, it’s a revolutionary knitting technology paired with an advanced selection of innovative fibers to create the ultimate in lightweight cut protection. The latest offering in our 21G line provides ANSI A4 cut resistance with unparalleled dexterity and extreme comfort that no other 21-gauge glove on the market can offer! Read More

  • Glove Guard® Clip

    Safety should never be compromised, especially when it comes to proper glove usage. The Glove Guard® clip enhances safety by encouraging employees to keep their gloves with them at all times. This reduces the risk of accidents and injuries on the job. By ensuring everyone has their gloves readily available, we help promote a culture of safety and efficiency. The Glove Guard® clip is designed to withstand the toughest work environments. Constructed from robust materials made in the USA, it can endure extreme conditions, including harsh weather, and rigorous activities. Read More

  • Safety Knives

    The Safety Knife Company has developed a quality range of safety knives for all industries. Designed so that fingers cannot get to the blades, these knives will safely cut through cardboard, tape, strapping, shrink or plastic wrap or a variety of other packing materials. Because these knives have no exposed blades and only cut cardboard deep, they will not only protect employees against lacerations but they will also save product. The Metal Detectable versions have revolutionary metal detectable polypropylene knife bodies specifically for the food and pharmaceutical industries. This material can be detected and rejected by typical detection machines and is X-ray visible. Read More

Featured

Webinars