OSHA to Issue Compliance Directive on H1N1-Related Inspections

To ensure the protection of frontline health care and emergency medical workers at high risk of infection with H1N1 virus, OSHA said it will soon issue a compliance directive to ensure uniform procedures when conducting inspections to identify and minimize or eliminate high to very high risk occupational exposures to the 2009 H1N1 influenza A virus. The agency said its directive will closely follow the CDC's Interim Guidance on Infection Control Measures for 2009 H1N1 Influenza in Healthcare Settings, Including Protection of Healthcare Personnel, posted last week on www.flu.gov.

In response to complaints, OSHA inspectors will ensure that health care employers implement a hierarchy of controls, including source control, engineering, and administrative measures, while encouraging vaccination and other work practices recommended by CDC. Where respirators are required to be used, the OSHA Respiratory Protection standard must be followed, including worker training and fit testing, the agency said.

CDC recommends the use of respiratory protection that is at least as protective as a fit tested disposable N95 respirator for healthcare personnel who are in close contact (within 6 feet) with patients with suspected or confirmed 2009 H1N1 influenza.

"Employers should do everything possible to protect their employees," said Acting Assistant Secretary of Labor Jordan Barab. He emphasized that where respirators are not commercially available, an employer will be considered to be in compliance if the employer can show that a good faith effort has been made to acquire respirators. The employer will also need to implement a hierarchy of controls such as feasible engineering controls, administrative controls, and the use, as appropriate, of personal protective equipment, such as gloves and respirators to protect workers while providing close-contact care.

Because a shortage of disposable N95 respirators is possible, employers are advised to monitor their supply, prioritize their use of disposable N95 respirators according to guidance provided by CDC, and to consider the use of elastomeric respirators and facemasks if severe shortages occur, OSHA said. Health care workers performing high hazard aerosol-generating procedures (e.g., bronchoscopy, open suctioning of airways, etc.) on a suspected or confirmed H1N1 patient must always use respirators at least as protective as a fit-tested N95, even where a respirator shortage exists. In addition, an employer must prioritize use of respirators to ensure that sufficient respirators are available for providing close-contact care for patients with aerosol-transmitted diseases such as tuberculosis.

Where OSHA inspectors determine that a facility has not violated any OSHA requirements but that additional measures could enhance the protection of employees, OSHA may provide the employer with a Hazard Alert Letter outlining suggested measures to further protect workers, the agency said.

Product Showcase

  • Safety Knives

    The Safety Knife Company has developed a quality range of safety knives for all industries. Designed so that fingers cannot get to the blades, these knives will safely cut through cardboard, tape, strapping, shrink or plastic wrap or a variety of other packing materials. Because these knives have no exposed blades and only cut cardboard deep, they will not only protect employees against lacerations but they will also save product. The Metal Detectable versions have revolutionary metal detectable polypropylene knife bodies specifically for the food and pharmaceutical industries. This material can be detected and rejected by typical detection machines and is X-ray visible. 3

  • NoiseCHEK Personal Noise Dosimeter

    SKC NoiseCHEK is the easiest-to-use dosimeter available! Designed specifically for OEHS professionals, SKC NoiseCHEK offers the easiest operation and accurate noise measurements. Everything you need is right in your palm. Pair Bluetooth models to your mobile devices and monitor workers remotely with the SmartWave dB app without interrupting workflow. Careful design features like a locking windscreen, sturdy clip, large front-lit display, bright status LEDs, and more make NoiseCHEK the top choice in noise dosimeters. Demo NoiseCHEK at AIHA Connect Booth 1003. 3

  • SECUPRO MARTEGO

    FOR HIGHEST DEMANDS. A cutting tool in which function and design go hand in hand. Meet the SECUPRO MARTEGO, our prize-winning squeeze-grip safety knife with fully automatic retractable blade for safety. • Ergonomically friendly trigger mechanism to engage the blade • Durable body made of aluminum • Safer alternative to fixed blade utility knives for general cutting tasks • 9 mm Cutting depth • Easy, tool free blade change Dimensions: L 6.10" L x 0.71" W x 1.91" H Weight: 3.70 oz Cutting Depth: 9 mm 3

Featured

Webinars