Make sure the weight rating of the ladder you choose is greater than your weight and all of the clothes, tools, and equipment you will be wearing/carrying. (Little Giant Ladder Systems photo)

Ladder Safety Month: Ladder Safety Tips

When climbed properly, a ladder in good condition will never be the cause of the accident.

Accidents happen for millions of reasons, but one simple truth is these accidents can be prevented. Three major causes are common in almost all accidents: not using the right tool for the job, using a damaged tool that hasn't been inspected, and not following the basic safety guideline for that tool. When people decide to get creative and cut corners to save a little time or effort, they expose themselves to accidents and injuries. Creativity is the enemy of safety.

Falls are a leading cause of accidents in the workplace, and ladders are involved in a high percentage of these incidents. But like other types of accidents, fall and ladder-related accidents are preventable by following three basic guidelines. Since this is an article about ladder safety, let's apply these guidelines to safe ladder use.

1. Use the right ladder for the job.
The first rule of using the right ladder is to use a ladder. Too often, people just grab the closest thing to them and end up standing on buckets or chairs instead of taking a few minutes to go get the right ladder. When choosing a ladder, make sure it is tall enough for the job. Per ANSI standards, ladders are marketed and sold by the total height, or the total section length, not the usable height.

Second, you should never stand on the top cap or use the top step of a stepladder (or A-frame). In practice, you should be 4 feet off the ground if you are using a 6-foot ladder. You will need the top 2 feet of the ladder to hold onto or lean against to maintain your three points of contact.

Extension ladders are sold by the total length of the sections and only mention the 3 feet of overlap in small print. A 20-foot extension ladder is two 10-foot sections, but because of the overlap needed, it is only 17 feet tall. If you are using it to climb on a roof, you should have 3 feet of ladder above the roofline to give you something to hold onto as you transition on and off the ladder.

Given all these factors, you almost always need a taller ladder than you think. Make sure the weight rating of the ladder you choose is greater than your weight and all of the clothes, tools, and equipment you will be wearing/carrying. Remember, when using any ladder, be aware of your surroundings and never use an aluminum ladder when working on or near electricity.

2. Inspect your ladder before each use.
If the ladder has any damage, do not use it. Ladders are built with a 4-to-1 safety ratio, meaning a ladder rated for 250 pounds was tested to hold 1,000 pounds when it was made. If the rungs or side rails are bent, broken, cracked, or split, you don't know what that ladder is rated for with the damage, so just don't use it.

One step a lot of people miss during the ladder inspection is to check the ladder's feet. They are made of a soft material and have tread like the tires on your vehicle. If the tread is worn, they should be replaced, just like your tires.

Ladders should be staked down or tied in place before they are used, but this rarely happens. Too often, the feet of the ladder are the only thing holding the ladder in place, so they should be kept in good condition. Remember, when climbed properly, a ladder in good condition will never be the cause of the accident.

3. Follow basic safety guidelines.
Ladders should be set on firm, level ground. Never use bricks or boards to level your ladder. Instead of building up the low side, dig out the high side for proper set-up. Aftermarket levelers can be added to ladders to help with leveling, and several manufacturers make models with integrated levelers.

Always face the ladder when using it and maintain three points of contact as you climb up and down. Never carry any tool or equipment up a ladder that might cause you to lose your balance. Heavy tools and equipment should be raised using a rope or lift. These rules are to help the climber safely ascend and descend the ladder.

If you are working at height from a ladder, make sure you lean your leg or hip into the ladder to maintain balance and contact with the ladder.

The most important rule of ladder use is to keep your body between the siderails. Never overreach. If you can't reach something without leaning outside of the siderails, climb down and move the ladder over. Losing balance while overreaching causes almost all disabling or fatal accidents.

The American Ladder Institute (ALI) believes all ladder-related accidents are preventable. To reduce the numbers of accidents and injuries involving ladders, the ALI is promoting Ladder Safety Month every March. National Ladder Safety Month is the only movement dedicated exclusively to the promotion of ladder safety at home and at work. During March 2019, National Ladder Safety Month will bring heightened awareness to the importance of the safe use of ladders through resources, training, and a national dialogue. To get involved, join us at www.laddersafetymonth.com.

This article originally appeared in the March 2019 issue of Occupational Health & Safety.

comments powered by Disqus

OH&S Digital Edition

  • OHS Magazine Digital Edition - July August 2019

    July/August 2019

    Featuring:

    • CHEMICAL SAFETY TRAINING
      Getting It Right
    • PROTECTIVE APPAREL
      Navigating Standards to Match Your Hazards
    • CONSTRUCTION SAFETY
      Just Add Water
    • FACILITY SAFETY
      Creating Safe Facilities
    View This Issue